After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi Nordic,
I was checking the ble_app_uart_coexist example application and it says it is a combination of both UART & Mesh. So would this support provisioning via mobile...
Hi, team. ********** environment : SDK : Mesh v3.2 (w/ SDK v15.3.0) SoC : nRF52840 IDE : SES ********** I am challenging to handle each event, such as Mesh receive interrupt...
Hi all,
Radio notification inactive state interrupt is coming but I was not able to do any action by comparing it.
I am thinking, if radio_evt is false then it is radio...
Hi,
I need trigger repeated SPIM via PPI for a batch of samples until the given RAM buffer is full. Then I need start another round of batch SPIM with another buffer.
...
Hi,
I am trying nrf52832 with pca10040 board. My app uses s112 soft device and also SPIM0 to collect data from a slave device. No event handler has been used when initializing...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
Dear Sir,
I have enabled my project for SPIM+EasyDMA.
I am configuring the SPIM transfer nrf_drv_spi_xfer with additional flags like,
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER...
nRF51822 QFAA
At first I set up the RAM size to 0x1F80, it works fine. However, after I try to use RTT to print log, I got the compile error: region RAM overflowed with...
