Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi,
We plan to measure the sleep current of the *whole* Thingy 91 system including nRF9160, nRF52840 and sensors. Do you have a firmware (sample app or similar) that puts...
To the kind attention of Nordic support team,
I'm evaluating your standard gzp example (proprietary_rf/gzll/gzp_dynamic_pairing, sdk15.3). From what I see, the device to...
Hi,
It seems that the nRF52811 for the most part draws less current the nRF52832. For example:
nRF52811: 1.4 μA at 3 V in System ON mode, no RAM retention, wake on RTC...
Hello,
I cannot reset the nRF52 DK while running on battery power. I've tried multiple examples of the SDK which didn't work. However, when connecting the DK via USB, the...
I don't know if I'm dealing with a hardware or software problem at this point. I have a custom NRF52810 board with chip antenna and no LF clock, in SES. In SDK 16 I modified...
I'm running the esb_ptx_pca10040e on a custom board with NRF52810. The program gets stuck on....
while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
This appears to be similar...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Previously we had a custom board...
Hi,
I was testing the various cases for DFU & I was looking for any possible solutions to fix the issue.
I flashed SD + bootloader (secure) + app from SDK 15.2 on the...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
Hi, I need to be able to count the number of packet Tx and Rx from one board to another in order to compute a packet loss ratio for certification purpose. To achieve this...
hi all:
Use PPI+timer+adc, in the following ways:
called stop, then unable to start adc, Couldn't get into the NRF_DRV_SAADC_EVT_DONE.
Could you tell me how?
