We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
I want to add a global variable that would increase every time the timer handler is called. I can't get it to work with static, volatile, or even pass on as variable. the...
Dear all,
I am very new to BLE developments and Nordic product, I have purchased the nRF52840 dongle to have a feeling on the product ( I understand I should get the nRF52840...
I have below queries Regarding Secure Boot and DFU:
1) Is the secure boot functionality available in nRF52840, if available please provide the procedure for doing it?
...
Hello, guys!
We are excited to start a new product prototyping by using Thingy:91 board. Consequently, I would have a few questions related to Thingy:91 configuration...
Based on sdk15.3, adding the 0x2902 descriptor to the rx characteristic of the ble_nus service resulted in an NRF_ERROR_FORBIDDEN error.
My code is as follows:
ble_add_descr_params_t...
Hi,
I'm using S112 v6.1.1 with SDK 15.3.0 on nRF52810.( I don't use bootloader )
I tried to search examples for using fstorage api on it.
But I couldn't get anything...
Hi,
Recently I came across this example which gives mesh & uart in single application. now i'm trying to add GATT proxy to it so that i can do provisioning via nrf mesh...
Hi,
I have read the dfu protocal and found that there are three types of dfu transfer which are identified by a firmware ID. Now I want to add a new part to update the user...
Dear,
I am using THINGY91 for proving my concept, I put THINGY91 in the freezer - to adapt to the temperature.
I am using NB_iot of telia (norway)
My problem is: sometimes...
Hi,
I am using the NRF52832 with softdevice 6.1.1
I am using the minimal ble_app_uart ecample, just changes the RX_PIN_NUMBER to 11 an TX_PIN_NUMBER to 12 to mach my board...
Hello ,
I want to read the values from tera term , and PCA10040 have to read that value on polling basis .
Then advertise that values / data as manufacturing data. i am...
Hi
it looks like my MQTT-SN is not working.
I am trying to run MQTTSN Example in nRF52840 devices. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
