Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hi, we are trying to get the nRF9160 connected to the internet again, we had it working 6 months ago.
Our hardware is 0.8.5
We are in Ireland where we only have NB-IOT...
Hi
I'm using the watchdog of the nRF52832 Rev. 1.
The PS V1.4 states that the maximum run current of the watchdog is 2uA while the typical current is only 0.3uA. Can you...
Hi,
I am migrating from SDK14.2 to SDK15.0 and I can compile now, but when runnning the nrfx_uart_init the hardware handshake signal RTS is high from the beginning.
...
I am running into compile errors in different places in the SDK where there are lines as shown below: #if (NRF_BLE_GATT_ENABLED) /* do something */ #endif It is a widely and...
Hello Team,
Currently, we are evaluating nRF52 using nRF52840DK for one of our upcoming project. Basically, our typical application involves sending 32 Bytes of command...
I am using nRF52840dk SDK15.3.0 ble_app_att_mtu_throughput example,in that example i included some part of ble_app_uart code. Now the issue i am facing is ble_link_ctx_manager...
im trying to do notification for characteristic of a service whenever i trying to notify from nrf mobile app the debug session in ses is stopping its play in few seconds
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Assume I have one FDS record. With this...
Hello,
If I understand well the characteristics of the Thingy.91 si that you supplie a firmware we can download and modify as we want because it is open source, is that...
We're trying to diagnose an issue that's occurred to at least two of our customers. For some reason, we've found two different iPhones that are seeing our reader (nRF52840...
Hello,
Float printk (%f and %0.2f) is not working. I use newlib and activated floats for print and scan support without success.
Configuration:
Version from 31 january...
Hello!
I use nRF52-DK wuth android device. DK connects to android device and works with it well. But I want a paired DK make unpaired from android device by performing unpair...
Hi,
I have requirement of BLE node to node communication in mesh network.
All the nodes should have single firmware which will be capable of publishing and subscribing...
Hi All,
We are trying to interface nRF52840 based custom board, manufactured using Config 6 schematic as the reference, with R-Pi to work as NCP. Please refer to the attached...
