When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Using LFRC as the softdevice LFCLK source, enabling and running the WDT causes the softdevice to hang until the watchdog reset when calling nrf_sdh_disable_request . This...
Hi
I'm trying to send fixed AT commands to the modem using a code based on this code from Rallare: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples...
Hi
I'm using a SparkFun Pro nRF52840 Mini which has a UART on PIN 17(TX) and 15(RX). I've written a very simple piece of code to blink the onboard LED on and off and to...
I update my software on the nrf52840 to the SDK16 and softdevice 7.
to get this software running i update the device family pack to version 8.29.0. (keil)
If i build the...
Hi,
There's no description at all in either the written text (31.3 SPI master transaction sequence) or the timing diagrams (Figure 71: SPI master transaction) showing precisely...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
In our setup we load merged hex file...
from this link
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
I gathered that nrfjprog is for flashing...
which is the Example code to test the NFC_Tag future in MDBT42 V P 512K V2 module.
i was using PCA10040 nrf52 development kit in that Example code is working same code not...
I want to disable and enable UART at runtime. I don't use DMA and interrupt.
I read this thread. https://devzone.nordicsemi.com/f/nordic-q-a/52496/nrf9160-uart-pull-up-and...
Hi.
I need to program for a set of NRF52832 with serial number from 403898368 to 403941418.
I am trying with nrfjprog --family NRF52 --memwr 0x10001080 --val %% --verify...
I am in the process of evaluating different BLE solutions for a project. The project consists of a pair of BLE-enabled devices which need to be able to go into dual-role mode...
Hi everyone
I don't really understand what the physical cell ID is. Is it a randomly generated ID created by the nRF9160 chip or a set ID within the cell?
As far as I...
Hello,
I am facing a really annoying issue when updating my SPI settings from the old nrf_drv_ towards the newer one nrfx , in SDK15. I am following the recommendtations...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) If I enable “Just works” and without...
