Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
hello, testing the spi examples of SDK16.0.0 I was trying to read a type k thermocouple with a max31856 on the nRF52840dk board, I made the connections of ss, sck, mosi, miso...
hey, i am strating with nrf52840 for thread.
i want to know if there is a need to add an antenna to the SoC? if not i can't visualize where is the antenna in the nrf52 DK...
Hi Nordic Team,
In my BLE project, the peripheral device has the ability to do both scanning and advertising. So please suggest a way of how the central device would know...
Hi all,
I have bought the NRF51822 evaluation kit ( NRF51822 ). I have some question about this.
1) Is it necessary to program the device?
2) what is the nominal operation...
SDK15.3
SES
nRF52840
Hello Folks,
I'm trying to reduce my applications power consumption further in system off mode. For testing my IO configuration and System...
I am trying to build one of the Thread examples.
nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b\examples\thread\simple_coap_client\pca10056
Keil uVusion V5.15
When...
Hi everyone,
my problem is pretty simple: we developed a custom board for the NRF52840 to work using a custom protocol or BLE. A few sensors are connected to the NRF using...
Hi,
I am using NCS v1.1.0 and modem fw 1.1.0.
We had prepared our application in NCS v1.0.0 and now i have moved it to v1.1.0.
In new sdk v1.1.0 ,When i try to get Address...
Hello , I am advertising from a nrf device with advertising interval of 40ms. and I want to measure this interval at scanning side.
How I can measure using timer , timer...
I am using nRF52 DK to evaluate the TX power settings using sd_ble_gap_tx_power_set command:
sd_ble_gap_tx_power_set ( BLE_GAP_TX_POWER_ROLE_CONN , m_conn_handle, tx_power...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
