I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Hi,
The documentation for the nRF52840 (section 6.20.15.9) states that RSSI has a typical accuracy of ±2 dBm. I have measured signal strength at multiple distances, and...
HI,ALL！
I use official routine development NRF51822，nRF51\nRF5_SDK_12.3.0_d7731ad\nRF5_SDK_12.3.0_d7731ad\examples\ble_central\experimental\ble_app_blinky_c\pca10028\s130...
Hi,
My problem is with generating interrupts in lsm6dso relative tilt mode.
I asked it in st community, but I didn´t get any answers.
I'm trying to implement a relative...
Hello,
I couldn't understand the predefined header files for the spi, so I'm building the spi code from scratch.
To build init_spi function, It's clearly mentioned in...
Hi,
We are currently trying to design a system using one of the nrf5 bluetooth chips. However, we are still in the process of designing a functional antenna and need to...
Hi, I am trying to implement an example that support multiple peripherals (HRS & UART). When I get a connection (from either) I get the BLE_GAP_EVT_CONNECTED. How can I differentiate...
What is exact difference between heartbeat and health models?
I know heartbeat can be used to detect node outage, but so can be health message?
So, which one should be...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
After Downgrade protection in the NRF9160 has been set with AT%XPRODDONE=1, switching it off with AT %XPRODDONE=0 returns ERROR. Is there a way to disable downgrade protection...
Hello DevZone,
Is there a way for hardware to update the timer capture register?
I want to create different frequencies using a single timer. Next to the timer, Bluetooth...
I am using Nordic proprietary RF receiver and transmitter. I want to display the received data on my serial terminal using UART pins (any 2 pins as Rx-Tx) .
When I tried...
Hello,
i'm writing a code for NRF9160DK where i plan to send a HTTP POST request to a test server when i push BUTTON1 on DK. To achieve this result i studied separately...
Hello,
I have an issue since today. Indeed I worked for a few weeks on the nRF52840 and everything was alright. I used a dock to connect the nRF52840 by serial port with...
