Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
i am using three s210 master devices to broadcast ANT messages to a s310 central device. The central connnects to a PC through USB dongle and BLE.
When broadcasting...
Hi,
I found several posts on this forum closely related to my problem, but non of this answer my needs. I try to program nRF51822AA with blinky example via Keil uVision...
Hi, in evothing and mbed all the UUID are 128bits long
however, in EK, the code use 16bit UUID
ex. nus.c the uuid is 0x0001 0x0002 0x0003
any one knows how to provide...
Hi,
I have just received my smart beacon kit (nRF51822 based), I have wired up my JLink programmer according to devzone.nordicsemi.com/.../
However I am having trouble...
Hi!
I'm building a mesh using beacons. Everything works good untill now, except beacons sometime stop advertising on its own. Beacon still works because he still connects...
Hi. We are going to mass production now and the lab that will certify our product says we need to have a special mode in the firmware that would do : modulated middle channel...
I want to make a custom board using nRF51822. Currently I am using nRF go studio starter kit and pca10005 board. I am using segger jtag programmer for loading code to the...
Hello,
I have a custom program based on the uart example. I can write to the device, but sending to the master fails.
I call the SendString code, but p_nus->is_notification_enabled...
Problem
I got some problem in change device name.
I found that the function of ble.gap.setDeviceName(deviceName) is useless.
So I've searching for another function...
Hi,
Does anyone know if there are plans to support RTX in the nRF52 SDK? It is included in the nRF51 SDK under external/rtx , and there is an example in examples/peripheral...
Hi,
I have purchased the nRF8001 DK and it came with no documentations. I downloaded the nRF8001 DK User Guide V1.1.
In this documentation, under section 1.3 there is...
I have setup environment on QT creator and i am using JLink GDB server debugger.The nordic chip is nrf51822 QF AA H0 and SDK is nrf51822 s110 version 8.1.0 .I read some posts...
I donwloaded the iOS nrf toolbox. I found that the app converts the glucose measurement to KG/L and not to mmol/l? The reading on the glucometer is in mg/dl so when I multiplied...
Hi,
I am trying to get my mesh running on the nRF52 Preview DK but calling
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
will break my program...
