Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
I'm seeing the resetreas show the CPU lock-up detected after I reboot. This error is occurring while using the ADC. What type of fault condition can cause a CPU lock-up detection...
Hey everyone,
I'm developing an application using the IoT SDK . The first part of the application consisted of a normal BLE peripheral to interact with an android app....
app_timer.h contains a useful macro for getting from milliseconds to a number of timer ticks, given a prescaler value with which the timer was started:
#define APP_TIMER_TICKS...
Hello,
May i know what will happen if we happen to assign the same pipe address for let's say pipe 1 and pipe 2?
Can we still receive data and be informed of the pipe...
Hi,
My goal is to send temperature values on the advertising so, I'm trying to get work this example, but i have an error about this lines of the code on keil:
advdata...
Hello, how can i modify the hrs_s_evt_handler() to initiate bonding only if it my configured belt address?
My Solution:
static void hrs_c_evt_handler(ble_hrs_c_t * p_hrs_c...
Hello, All.
I want to know AppID in iPhone's App using ANCS.
(for example, Facebook App's AppID is "com.facebook.Facebook",
Facetime's AppID is "com.apple.facetime")...
Hi Nordics!
I want to add custom service into ANCS example for android.
But I cannot understand how to add custom service stably.
First, I just added my custom service...
I have compiled the nRF51-ble-bcast-mesh 's examples: "LED_mesh_SDK7" and "BLE_Gateway_SDK7" on Keil uVision v5.14.0.0. But, I am facing problems flashing them on to my nRF51422...
I have a problem that I can't figure out. I have a custom board with an nRF51822 QFAB. The board will run a test application that uses nrf_delay_ms() to toggle an output pin...
Hi!
I have reviewed the NRF518 reference design, i.e., case "PCB layout recommendations for the NRF51822 WLCSP62 package" and the layout pdf files provided therein:
...
Hi
I have read various things about this so I would like to confirm
What is the best way to set the bluetooth address of my device ? Is it built in by nordic ?
Or is it...
