Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
We have a BLE peripheral that has a button interface and nothing else. We would like to add some security so only certain smartphones can send/receive commands from it. An...
Hello all,
I'm using nrf51822 xxac on my project, however, I sometimes got feedback from my customer and said the OTA is not work. My device can't turn to DFU mode for firmware...
Hi, I bought the nrf51822-beacon kit and nrf51-dk including TC2030-CTX-NL connector for connecting them each other through the Debug out pin on the nRF51-DK.
I can't find...
According to the following sources.
advertising_init() -> advertising_update() -> advertising_update() -> ....
UUID, Mayjor, Minor is set in the advertising_init()....
Dear All
I'd like to know how to use Master Control Panel as non Administrator User.
I got and installed MCP v3.8.0.7, but the MCP cannot start on my PC.
Maybe it's...
Hi everyone,
I want to know the original interrupt priority of nrf51822, without using soft device or using NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority). I also want...
Hello everyone!
Just have a look at this beautiful drawing. (Red: what has to be done. Black: Can it be done this way?)
I only have some rudimental experiences in...
Hello! I trying to send message from peripheral to central. On peripheral characteristics are changes with delay. To change characteristics I use this function:
void send_char_data...
Im using the PCA10031. Placed it in the my laptop usb and installed the nRF go and keil mdk arm and nrf51 sdk.
Using the pack installer, which example should I use to be...
Hi,
Can anyone tell me, how the handle value is assigned for a profile. In my master control panel i can see the handle values assigned for every services, but it is not...
Use the beacon want to send with the temperature and remaining battery power.
But beacon of UUID, Major, Minor, Type, etc. The only information in the beacon 26Byte.
...
Hello,
We are developing an application which is using the app_scheduler (especially to put events etc.)
It seems that sometimes (very rarely) we detected a Hard Fault...
I have 4 buttons in my circuit with a nRF51822QQAC (a RAYTAC MDBT40 module on a custom PCB), I am using a very simple printf to check which ones are pressed, the internal...
I've followed this for assistance, but I'm stuck:
https://devzone.nordicsemi.com/question/17846/nonvolatile-memory-access/
I can read from flash, but I can't write to...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
