I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
nrf 52832 is able to run in 64 MHz using external 32 MHz crystal.
I wondered if I can use an external 16 MHz crystal, and get the CPU to run in 32 Mhz.
Thanks
...
Hi, All
sdk v7.2, IOS 9.1
I know after peering with IRK, iOS will connect 51822 actively.
There're some issue in my project. It's not certain happen.
At most of...
I developed an application program and I have a hex file generated from mbed compiler, and would like to know if I flash this hex file using a J-link interface on NRF51822...
I'm just getting started with the nRF51 DK. I've successfully "passed" the blinky test and I'm now trying to test the HRT example (ble_app_hrs_s110_pca10028). I found another...
According the the nRF Logger app on Android I get a GATT CONN TIMEOUT error when running the HRS demo code on a nRF51822 QFAAG2 device (with custom_board.h) and connecting...
I have the application saving off the information it should from the Nordic documentation titled "Sharing bonding information" which is part of the Info center software developers...
Hi all,
I have some question with ble_ancs_c sample code.
SoftDevice: nRF51822 S110 V8.0.0
SDK: nRF51_SDK_9.0.0_2e23562
I add ble_ancs_c_request_attrs function...
Hi
After reading different threads I figured out that I can program my Smart Beacons kit using NRF51-DK. Correct?
And to do so I need TC2030 tag-connect cable?
If yes...
I am using the spi slave example code from SDK 0.9.2 and connect the board to an Atmel SAM4S who is the SPI master. I can see that every time the CS signal is released from...
I want to make nrf51822 with accelerometer.But Keil compiler dont know.What I do?
It was given as examples of programs I want to do. devzone.nordicsemi.com/.../.I
I want...
Hello Guys,
I want to go with nordic solution for the bluetooth low energy application. Can anyone please explain me how much it will cost to develop your own module including...
hiii....
i am developing a custom profile with five services... i want to make these 5 services and its characteristics available only for some authorized devices.. ie...
I am working on a custom service using and nrf51822 device. SDK7.1 SD7.1
My security parameters are as follows:
#define SEC_PARAM_TIMEOUT 30 /**< Timeout for Pairing...
