Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I have a program that it works fine with nRF51-DK, but I want build a PCB with the Waveshare Mini nRF51822 module.
What do I need to program this module? With the...
Hello
When refering to the documentation its stated:
"The DTM application is stand-alone. Therefore the S110 SoftDevice must be erased in the nRF51822 device. "
Is this...
when i download the 7.0.0 softdevice and the demo project "Nordic\nrf51822\Board\pca10001\s110\experimental\ble_app_uart" to my nRF51822 board,it works well,but use the 8...
I have changed some where of bps demo.one of is i use the app_timer_create() api creat the time use to send digtal periodicity,but after changed the nrf51822 could connect...
Hello Everyone,
I flashed the nrf51DK by using the basic blinky example after that i tried to flash the UART example program it is displaying programming is done, but still...
Dear Nordic Developers
I'm using ble_app_uart example with PCA10028 development board. SDK version is 8.0.0.
I'm trying to program the PCA10028 board for having a static...
Hello Everyone ,
I am using nrf51DK i have compiled the basic blinky program it get downloaded properly and also i saw the output after that i compiled the ble_uart_example...
Hi,
I'm searching a way to create a function which would be a timer function (so, this function will have an int number as input parameter), and during this delay, I would...
On this question I read that S110 is blocking CPU a lot during advertising/connection ( devzone.nordicsemi.com/.../).
On this other question they say that you can change...
I am using two nrf51822 ek. one is programmed with multilink central and other is programmed with multilink peripheral. when i press the button on multilink peripheral, i...
I need to connect to a beacon with a scanner nRF51 using the advertising data of the beacon. Then i need to get the service and characteristics of the beacon.
Thanks
Hello everyone,
i am trying to compile the Ble-UART_example but everytime it shows this error 'GPIOTE_config_irq_priority is undefined ) and i dont know what went wrong...
I have tried to flash my application targeting nRF51822 on our board by using a Segger on nRF51 DK. However, Keil compiler always shows that it couldn't find any nRF51822...