Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi All,
I am using the nrf_udp_client example project in IoT SDK as the code base for testing the UDP communication.
For network topology, the nrf51-DK plays the role...
Hi everyone:
I have some question about nrf51822 power on sleep mode
in example ble_app_hrs have a "power_manage" function and it will make the system go into power...
Hello all,
I have a simple C++ application flashed to my device to operate the UART - every time I send a char from an external source, the device appears to reset - specifically...
Hello
I was wondering if it is possible to run to separate LP-comparators on the PCA10001? I've taken a look at the example code for LP-comparator in the SDK, and i was...
I'm using interrupt_handler.c for a bootloader without a softdevice from this source . Interrupt handling in the main app seems to work fine. But interrupts in the bootloader...
Hi,
In the nrf51_bitfields.h file, I can see definitions for two registers POWER_RAMON and POWER_RAMONB.
But I don't see this RAMONB in th nRF51 reference manual and...
hello, I bought one of these dongles on ebay www.ebay.com/.../201229095155
i was hoping to communicate to the nrf24l01 modules with my pc serially, but I can't get the...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello there, I do not understand the definition Nordic has provided for the "SPI_slave_event_handler_register" function bellow. My understanding is when SPI slave driver occurs...
I need to write to a variable when a particular characteristic is written (from my "on_write" function), and be able to read this variable from main context.
From the SoftDevice...
Hi everyone :
I'm trying to used ble_app_beacon and I want to combine it into ble_ app_hrs
so i add some code as followed:
static void advertising_init(void){
uint32_t...
We're sending packets from a nRF51422 usb dongle to a nRF51422 dev board running some modified Nordic UART example code. We send 100kB of data over the connection to work...
Hello :)
For the code below, why are we defining the _wfi while in the code we only use _WFI() for addressing the function? Also once we use _asm volatile ("wfi); isnt the...
Hi:
my sdk is about 96k,and i use 51822QFAC,but it's flash is 256K,(256K-88K)/2=84K,so it is not enough for me,how should i do,if i add a external flash is ok or do you...
