در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
Hi,
I have searched for examples which will use passkey to connect with android, but didnt find any.
I want ble_app_hrs example to connect with nRFConnect in android by...
HI，i develop my project base on “examples\ble_peripheral\ble_app_uart” and “nRF UART v2.0”。i hava large data transmit from phone（androd） to nrf52832。
but when send a package...
I need to save some data on the flash storage. This data will be some structures and I will write, read and modify them as and when required. I am also using peer manager...
Hello
I came across interesting problem I couldn't find answer to.
In my project bss size printed by arm-none-eabi-size is larger than the value that can be calculated...
I'm testing with ANCS example(SDK11.0.0), PCA10028 and Iphone, observing packet with sniffer.
at the first connection,
master sent EDIV( 0x0 ), Rand( 0x0 ), SKDm and...
I'm using an Nrf52 with S132v3.0
I'm using Peer Manager to manage pairing and bonding.
I'm running as a central connecting to a peripheral (iOS/Android peripheral).
I...
Is there any way for the application to be notified by the S110 when a central reads/scans an attribute in the peripheral in response to its broadcast?
There are events...
hi,all
i use use dongle as packet sniffer.when the phone can not connect my device,the dongle can not receive CONNECT_REQ PDU.if the phone can connect with my device,the...
Hi,
I am using legacy version of DFU for my application and would like to use the appropriate version. However, using pip the only available versions are 1.1.1 and beyond...
Dear NORDIC
I have one strange issue:
My nRF52 app work well, then I use Android phone connect to it, it's OK.
Then Android phone cancel pair, so nRF52 disconnect,
...
i want to run simple compiled example .its very basic question.i need your to take start ??which example i compiled first and what the devices i have required to test it
