Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hello!
We are doing transfer from an Android app to a device using nRF52. We don't get the transfer speed I have seen other achieve. I get between 8.5-10 kbps. As a reference...
I added a few custom services the ble_app_hrs code. I tried to flash the code, it was successful, the device is advertising but not connecting in the nRF connect app. What...
hi,
i started a project based on the ble_app_uart_c example and i have a working connection with a central and a peripheral board. now i'd like to have two peripherals...
Hi fellows,
I'm trying to control accurate/deterministic timing of the first bit from MOSI PIN of SPIM, employing EasyDMA.
According to Figure 69 SPI master with EsayDMA...
Hello,
I noticed the linker file we were using was for the nRF52832_xxAA so I got the nrf52832_xxab.icf from C:\Program Files (x86)\IAR Systems\Embedded Workbench 8.0\arm...
Hello,
I need to add firmware update process via air to my NRF 51822 device that runs application code on stack 12.2. How can i achieve this?
Do i need to add...
Hello,
I want to develop small modules with smart BLE that only sends advertise every 2seconds.
Do you think that the Central module can see all peripherals if the installation...
Hej, I just spent plenty of time finding an answer on above error within here with no luck. Since
there are certainly others facing this problem, I hereby post my solution...
sdkconfig.txt mainc.txt (/attachment/6fb97103178e9eb2c30302351e63ce8f)Can you please tell whether i follow the the entire tutorial as in the link or just the first step for...
Hello, when invoking sd_ble_gatts_hvx, it returned NRF_ERROR_INVALID_STATE (0x00000008), I wanna know what are the list of possible errors, here are a list I made:
CCCD...
Ciao all,
Two weeks ago I have started to learn about beacons and their usage. I have bought pca10040 development kit and designed custom nRF52832 based beacons. After...
Hi,
I've just hit a strange issue with SDK 12.1 on nRF52832.
Usually on BLE_GAP_EVT_DISCONNECTED , sd_ble_gap_adv_start gets called to start advertising and everything...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
