nRF NCS 3.0.x
Target : nrf5340dk or native_sim
What is the latest recommendation on build environment (assuming preference is a docker image for consistency of build...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
I know this might be a dumb question to you all, I am first time doing this sort of work
How to connect Jlink to NRF52? I need to flash a custom built BLE board with new...
I'm running on a nrf51822 chip, using Keil and a JLink Segger programmer. I'm running on SDK 12.2.0 and I believe I was correct in choosing pca 10028 s130 but I'm not 100...
I followed the instruction and installed the latest version of nRFgo 64bit v1.21.2. After installation, I can not find ble-sniffer___SNIFFER.zip at all.
Where can I find...
Hello,
I was able to get SEGGER_RTT_WriteString() to work correctly, however SEGGER_RTT_printf keeps giving me this issue when compiling:
._build\nrf52832_xxaa.axf:...
I am programming a beacon, first I had some problems using sd_ble_gap_adv_start() so I changed to ble_advertising_start() .
Now I have a problem when compiling:
_build...
I'm trying to use the PPK with an nRF51 dev board, and I'm getting this output whenever I try to start the PPK Software:
Checking installed packages
pyside: 1.2.4
pyqtgraph...
I tested a 23byte data transition in iPhone 5s with Softdevice 3.1.0, sdk12.2 .
it is ok. I know that iphone 5s is ble 4.0.
So I thought it would be possible on Android...
How do I set TIMER2 to interrupt every 1 ms?
Sounds like a very basic question, but I haven't succeed. For TIMER1 I can get it working, but for TIMER2 the highest frequecy...
I am using SAADC and reading in 1 analog channel. The data sheet says that scan mode is enabled when 2 or more channels are turned on. What if I am only using 1 channel ?...
Hello, after I program bootloader, sd, application, I did the following command to do read back protection,
nrfjprog --rbp ALL -f NRF51
But, even though I still can...
Is there a way to achieve what bsp_event_to_button_action_assign(button_id, action, event) does but using my own button?
The functions requires a button_id like 0,1,2,3...
When I use NRF_LOG_GETCHAR() witn nRF52 DK and onboard SEGGER UART it stops in next NRF_LOG_INFO(). Also after ARM reset it keeps in this error state. It seems that SEGGER...
Hello,
I'm trying to install wireshark sniffer on ubuntu 14.04 with PCA10031.
I follow this guide : devzone.nordicsemi.com/.../
But when I launch sudo python example_linux...
Hi,
I am trying to replicate the "Throughput and long range demo" from devzone.nordicsemi.com/.../
I have two nRF52840 boards. I am using IAR studio. I can compile,...
Hi,
i am working on TWI sensor example in SDK1. in which i connected SCL And SDA pins tonRF52 dk boards sca and scl pins. and connected voltage and ground. when i run the...
