According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
I would like to use twenty concurrent connections. As I understand I should set ble_cfg.gap_cfg.role_count_cfg.periph_role_count = 20 and ble_cfg.conn_cfg.params.gap_conn_cfg...
Hello,
I have read with a lot of interest the documentation associated to the "multiprotocol support" associated to the nRF5 SDK for Thread v0.10.0.
As far as I understood...
This is a more specific counterpart to a question I posted on StackExchange . If you want to know more about the attack itself, check that out, but here, I'm asking for a...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
In order to prevent communication from middle-man attack, I append the signature after ECDH publickey. However, though I get the correct share secret by ECDH, I fail in verifying...
Hi,
I'm using the bluetooth 5.0 and base on the mutilink_center example to add a peripheral and a center. Because I want the center to connect two type device. It could...
Hello,
I have two identical devices with Laird's BL600 chip (that uses NRF51822). They are initialized as NRF_GZLL_MODE_DEVICE and use GZP library (without encryption ...
Hi,
I am trying to write my own bootloader. I gather new image via serial and store it in flash in my application at 0x30000 then invoke reset and in bootloader I want...
Hi,
I was testing the pwr_mgmt project in the nRF5_SDK_13.0.0 with my 52DK, the system off mode seems work fine ,cause the log information is right,but the question is...
Hi,
We are working with NRF 51822 in a multi-role arrangement (SDK 12.3.0, s130_nrf51_2.0.1_softdevice) where one NRF51 will be connected to a phone in peripheral mode and...
when i use pc tools or APP except "nRF Connect" to connect my 51822,i can not find some parameter,so i want to know in example "ble_app_uart",how to set up connect parameter...
So apparently, for ble, all CCCDs, regardless of what the UUID of a characteristic is, is
00002902-0000-1000-8000-00805f9b34fb
And to access that, the proper step...
