I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Dear sirs
Good evening !
I´m using the RF24.h library in order to develop a system that comunicates in peer-to-peer mode.
When I transmit 3 bytes towards a receiver...
I'm hoping someone can tell me if I'm on the right track. Do I understand correctly that on an nrf51, the LPCOMP can be configured to wake the processor on an analog input...
Hello,
I was wondering how is calcualted or read on the Thingy firmware the variable w for the quaternion used in the Gyroscope readings.
Looking into m_motion.c in the...
The power data of lfclk is measured under the same hardware and software conditions. When we used two model chips, we found a difference of 1 microamps for the value of the...
hi, I am trying to make buttonless dfu working, but I am not sure how to do that. I am using SDK 14.2.0 with nrf52832. right now, the ble dfu example works. and I found in...
hi
i am using nrf52 dk with MPU 9255 as slave.which pin number of nrf52 dk should i use for 4 wire as SDA, ADO, SCL, NCS.In the attached file ,it is given as p0.20(MOSI...
I'm developing custom PCB with the nRF52832, and I would like to use the ITM for debugging. I don't have a J-trace or equivalent hardware, so everything will have to be done...
I was reading the tutorial :
https://devzone.nordicsemi.com/b/blog/posts/bluetooth-smart-and-the-nordics-softdevices-part-1
it says about how a ble device can advertise...
In Mesh SDK, there are 3 versions available for s132 softdevice: s132_3.1.0, s132_4.0.4, s132_5.0.0.
The question is, should I always use the latest version available? If...
Before I use 51822QFAC(with 32K RAM)， add I must use 51822QFAA(with 16K RAM)。
I have modify IRAM area，like this
IRAM: 0x20001FE8 0x2018.
and selete device is 51822QFAA...
We are designing the nrf52840 with high voltage mode and both DCDC regulators.
Where can I find the requirements for the external circuitry, like the inductors. For now...
Hi,
1. what the DC2DC switching frequency of nRF52832?
2. at nRF52840 the inductor should be 10uH with tolerance +-10% but for nRF52832 this inductor can be with tolerance...
Hey everyone,
I've been trying to get this basic bare-metal application to work. I don't need a softdevice as I'm just trying to turn on an LED. The application compiles...
Could not connect to the nRF52840 preview DK eval kit running the ble_peripheral/ble_app_uart firmware to iOS 11 device running the nRF connect or toolbox apps. We tried on...
Hi:Nordic
Because the nrf52832 can't read 8bit parallel data from GPIOs to RAM with EeayDMA . So I want to use 3 SPI simultaneously to write data to ram with EeayDMA, can...
