Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hello.
I need to use LESC numeric comparison pairing.
It seems that the PIN is automatically and ramdomly generated after the connection occurs.
I would need to manage...
I am running a nrf52 with IOT sdk's Cloud CoAP example. I am wondering about the parameters that I would need to integrate this into a product. These include the stack size...
Hello,
I am using 52832 to test ble data throughput. When two devices are close to each other, the throughput can reach 80kB/s, but if the distance is about 4 meters, the...
The nRF51422 product specification says that you have to use a +-40 ppm crystal for BLE applications.
On DigiKey, there are 2 columns for 2520 crystals: frequency stability...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello, I downloaded the ble_mesh_v0.9.1-Alpha source code from nordic website, and tried to port it to my pca10056 devboard.
When doing so, I noticed that some function...
Hi All,
I would like to use FreeRTOS in my project. I try to play with the examples/ble_peripheral/ble_app_hrs_freertos project.
I have enabled logging with RTT. The...
Hi, when reading BLE Mesh specs, this paragraph caught my attention:
Messages may support a delay parameter that indicates a delay between receiving a message and
starting...
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation folder for details....
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
when use the sd_ble_gatts_hvx() send data and printf() the value below
p_ble_evt->evt.gatts_evt.params.hvc.handle
p_ble_evt->evt.gatts_evt.params.sys_attr_missing.hint...
