Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Written a custom script to write product model no into UICR Registers. After updating Model No, DFU was getting failed at state 6 i.e after updating init data after moving...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
I am trying to sent multiple messages from nrf52dk but it seems that i can sent only 7 even if i put a delay between messages . Any suggestions ?
for(int x =0;x < numberofevents;x...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
I used two PCA10040 boards to test the UART serialization function with s332 softdevice.
I add my ANT_PLUS_NETWORK_KEY and build the examples "experimental_ant_ble" is working...
Hi, I have a strange problem. I am new to nRF IC's.
I recently took a new job...the person who wrote the code for our nRF51422 lost some source code in the process of changing...
I'm trying to create a HID bluetooth device with multiple connections to centrals. Looking at the ble_hids service implementation, the on_connect event handler sets the connection...
Hello!
I'm looking to build an application on nrf52840 DK that collects multiple sensor values and transmits it over Bluetooth. For now, I don't have a bluetooth application...
Hey I'm doing some SPI transfer in response to a GPIOTE in event. I'm targeting the NRF52840 and kind of went with the following answer:
https://devzone.nordicsemi.com...
Hello,
My setup is pca10040, sdk 14.2, s132.
I have tried firstly the blocking mode function and it is not reacting. After that I used SAADC module in a non blocking mode...
Is it possible to use the mbr, currently inside the softdevice, without the softdevice? Can we use the combination MBR/Application/bootloader? So we have a lot more flash...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
When completed my program is supposed to read data from sensor (via I2C), store it in...
