Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
Is there someone I can contact about acquiring some sample chips for prototyping? The normal distributors don't seem to have any information regarding the engineering samples...
Hello,
I am currently working on a project involving the nRF52DK to be a central device.
The peripheral device is based on the Nordic Uart service with minor changes...
hi，
i tried add ancs to the s130 ble_app_hrs_rscs_relay demo， when i use iphone5s to connect， the uart display as follow，but when i receive a message or a call， the software...
In GATT Packet transfer, is there occurs any packet loss and retrial?
I'm trying to connect about -90 Rssi dBm peripheral device with my nRF51-dk.
In this far range...
Hello,
when I was working on MSP430 I used to place the firmware version constant at a known address in flash so that it can be verified which firmware version is flashed...
I was having some troubles using the app_timer (RTC1) shortly after mesh startup, so I enabled the PIN_IN_CB and PIN_IN_TS debug pins, and saw some interesting behavior. ...
Hello all,
am trying to configure 3 adc channels in a way to have conversion in 3 differents pins, without usin timer and ppi. so I implement the following code, the problem...
Hi
May i know what would be the debugging procedure using segger-RTT for nrf52840 and what is the debugging Hardware Required ?
Thanks and Regards,
R Madhu.
I know BLE5 is the future of IoT. I also want to invest on it.
But how to setup a complete BLE5 environment? In China, IPv6 has not been supported. Therefore, 6LowPAN/Thread...
