I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi, Nordic!
We have two PDK-NRF52840 and custom boards with NRF52840 chips.
2 from 5 chips have a broken bit in RAM. This is different places.
For example:
Is this...
Hi all,
if i buy 2 nrf52840dk:
Is possible create an audio connection like intercom between the two dk?
Can I send my voice from "dev board 1" to "dev board 2"?! and...
Hi,
I beginning now to program nrf51822. I would like to let the nrf51822 wake up after 3 hours by using a software timer interrupt.
Should I use power_manage()? Before...
Hi,
I'm trying to configure custom local GATT server on nRF8001 device. I added a custom service with multiple characteristics, but I can't generate source files. It says...
Hello!
I'm doing master thesis and I've chosen WT51822-S4AT board for BLE. I've made board successfully and programmed uC to send serial data to BLE.
I'm able to received...
Hi all,
I am using nRF52832 DK for my project. I need to config BLE for connecting with my phone. After a lot searching, I know that I can use softdevice API for configuring...
I mashed up RTC and SAADC examples. The files of the project are attached in the end of the post. The problem is that after the first iteration (I want to sample audio for...
Hello,
I am using developping on an nRF51822 with SDK12. In our application, our custom board need to communicate with a computer through a USB communication. I am not...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
