Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
Hello,
I'm new in programming beacons and ble sofware. I'm using the nRF51822 Beacon with S110 and the USB Dongle.
I updated the beacon with the example ble_app_beacon via...
hello, i am new to the Nordic controllers.I am having 2 doubts.
i want to modified saadc example code in keil 5 for that i want to add "app_timer.h" header file...
Hi guys.
I want to make use of CLI in my existing project based on ble_app_uart .
I was looking at the diferences of there sdk_config.h and there is a lot of stuff happening...
sd_flash_write(((uint32_t *)storage_addr),
(uint32_t *)p_data_addr,
size / sizeof(uint32_t));
why here size value is divided by sizeof(uint32_t).
what is byte value...
Hi,
I'm trying to adapt the HRS/RSCS relay example from the SDK to use the Nordic UART service instead. Currently I can connect to the central just fine, but if I try to...
I'm using RTX timers on NRF51 and I'm getting a 7ms per second error. (I.e. osDelay(1000) takes 1007ms).
It appears that NRF_RTC1 is configured incorrectly in SDK examples...
Hello, I am working on NRF52 customer board + SDK_13.0.0_04a0bfd
I start with ble_app_uart example, I use interrupt tigger a repeat timer(500Hz, 400 times) to sample 6 channels...
I'm having major troubles with my debugging setup using a nRF51 DK (PCA10028 V1.2.0).
When I try to connect to the board I want to debug/program (which has an BlueMod ...
Hi Everyone,
I'm currently busy going through the OpenThread API and examples to better understand what all the functions do. However, I don't fully understand where the...
Preferences: nRF52832 chip, s132_nrf52_4.0.2_softdevice
Two or more nRF52832 chip are connected to iOS and Android.
And do bluetooth off in smart phone.
this case, bluetooth...
This suggests it should be possible to change the beacon advertising content in response to events such as a GPIO input.
I'm using nrf52 DK running the beacon example (SDK...
Hi,
What should I add to the makefiles to be able to generate an assembly code? Something similar to what is seen in the debug mode of Eclipse. I have tried -S/s but it...
Hi
I want to porting to nRF52840 but since S140 SoftDevice Specification documentation doesn't exist
I can not proceed with porintg.
I need S140's detail memory map...
I am using s132_nrf52_3.0.0_softdevice.hex and sdk12 and compiling with arm-none-eabi-gcc. The problem is that the bluetooth set up just jams at:
// Enable BLE stack.
...
