HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
In the PS v1.4 pages 13-15 related to the QFN package.
Pins 11, 12 (P0.09, P0.10) are marked with the note '1'.
On page 15, at the bottom, the notes are enumerated:
...
I have a button that will put my device into pairing mode. While in this mode, I want central devices that connect to form bonds so that when not in pairing mode I have a...
Here I document how, in Eclipse, to start two, concurrent debugging sessions to two NRF5DK boards (or other debugging probes) , connected to different USB ports of the same...
Hello everybody,
I have problems with selectivity when I scan. There are 5 peripheral devices with different " DEVICE_NAME " but the same UUID and type (same " ble_uuid_t...
Hi, I am working on a custom board of NRF 51822 driving multiple leds from pin 21 to 30. I am trying to get and transmit the status of all the pins with help of bsp functions...
Hi,
We'd like to implement a feature that allows changing a BLE connection from [central device #1 -> peripheral] to [central device #2 -> same peripheral] (similar to Apple...
Dear friends,
The nRF Connect BLE app is connected with a local device acted as Master. The app supports the configuration of the local device's GATT attribute table, and...
Hello,
After i uploaded a program on my nRF52832 i couldn't enter debug or reprogram the chip. This is the error i get when trying to erase the chip using Segger J-Flash...
Hi,
I am using peer manager to use static passkey with nrf51822, sdk11 and s130 v2.
Is the "case PM_EVT_CONN_SEC_START:" the best place to put sd_ble_gap_tx_power_set...
I know this question has been asked before. As a beginner to Nordic, I tried to get the information here, but ended up even more confused.
I am trying to set up a Bluetooth...
Hi,
I developed a unit on NRF52 which is "CENTRAL". This unit connects to multiple "PHERIPHERAL" units and it's working great.
Now, i need to connect this "CENTRAL" unit...
app_timer.h is include two times in : examples\ble_peripheral\ble_app_ancs_c\main.c examples\peripheral\spi_master_using_nrf_spi_mngr\main.c examples\peripheral\twi_master_using_nrf_twi_mngr...
We are using the nRF52832 to scan for surrounding beacons on an interval (scan for 60 seconds, sleep for 30 minutes). During some of these scans, not all beacons are picked...
Hi,
I'm trying to run some examples using my nRF52840 . I noticed that the BLE header files used in the SDK 14.2.0 are different than what's in the standalone S140 (6.0...
