But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello Nordic,
we are going to perform RF-PHY test for nRF52810 at DEKRA. Can you help us with IXIT filling? There is one answer available at devzone:
https://devzone.nordicsemi...
hi
i have written a service and added 3 characteristics .In master controll panel i am trying to discover services.i see these logs . Device gets disconnected while discovering...
Running the `examples/ble_app_uart` on below environments, in Nexus6 only, it causes that local name byte array will be broken.
* DK：nRF52 PCA10040 v0.9.0 * SDK：14.2.0 ...
Hello all,
I am working on a college project where i need to interface a SD card, an OLED display along with BLE support on nRF52DK, PCA10040, s132, SDK14.1, Segger embedded...
Hi Now I am developing the application to measure PER of each data rate of BLE.
For packet exchange, I use IPSP example in the latest nRF5 SDK version 15, s140.
I could...
As far as I can tell there is a sign error bug when setting the tx power to a negative value. ble_dtm.c uses an int32_t to represent the tx power so when calling dtm_set_txpower...
I have compiled and debugged the temperature_pca10036 code from nRF5_SDK_v11.0. I have used termite terminal for getting info about transferring of data from nRF52832 board...
Hi,
I am using nRF52 board and want to change the RESET output from P0.21 to P0.2.
-I have CONFIG_GPIO_AS_PINRESET defined in the makefile.
-When debugging I can...
First, we implemented ble secure dfu application on nrf51dk. After, we want to program nrf51822xxaa device with same ble secure dfu app. In addition, we saw about rom/ram...
Hello Friends,
I've Get my Thingy from Nordic Tech tour and have a good time with it.
I think everything is perfert, but location of ccs811 ( Tvoc +eCO2 Sensor ) is...
Hi Nordic & friends,
As I know, DLE(data length extension) is not supported in S112. We are using nrf52810 in our development, so I make a test.
A long data packet(>=20...
How can I perform multiple A / D conversion?
I created a program with reference to the method of the old version of A / D conversion, but the function name and argument used...
Noted that the new V15 SDK for IAR does not have linker config file set correctly on ble_app_blinky_pca10040e_s112 project. The .intvec start location was set to 0x19000 and...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
