Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hi Experts,
I have looked into the Mesh SDK for several days, i found one question is the device how to handle the same message they transmitted before after power reset...
To the kind attention of Nordic support team,
I have been doing the pairing between two devices using nrf gazell secured library. Then, what I want to do, it is to read...
Hi,
We plan to measure the sleep current of the *whole* Thingy 91 system including nRF9160, nRF52840 and sensors. Do you have a firmware (sample app or similar) that puts...
To the kind attention of Nordic support team,
I'm evaluating your standard gzp example (proprietary_rf/gzll/gzp_dynamic_pairing, sdk15.3). From what I see, the device to...
Hi,
It seems that the nRF52811 for the most part draws less current the nRF52832. For example:
nRF52811: 1.4 μA at 3 V in System ON mode, no RAM retention, wake on RTC...
Hello,
I cannot reset the nRF52 DK while running on battery power. I've tried multiple examples of the SDK which didn't work. However, when connecting the DK via USB, the...
I don't know if I'm dealing with a hardware or software problem at this point. I have a custom NRF52810 board with chip antenna and no LF clock, in SES. In SDK 16 I modified...
I'm running the esb_ptx_pca10040e on a custom board with NRF52810. The program gets stuck on....
while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
This appears to be similar...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Previously we had a custom board...
Hi,
I was testing the various cases for DFU & I was looking for any possible solutions to fix the issue.
I flashed SD + bootloader (secure) + app from SDK 15.2 on the...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
