Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I have the same problem as this post . The difference is my SPI is sending out junk instead of stucking. I have tried the solution in the original post but no avail...
We bought 3x nRF52833dk (pca10100). Because the nRF5SDK V16 has only a few pca10100 examples we searched this forum and followed the advice: Change the "Linker->Sections Placement...
Hello,
I'd like to look at the Zigbee network traffic to/from/between IKEA Trådfri devices, but am unable to see any traffic when using nRF Sniffer from Wireshark. Unfortunately...
Hi,
I have an nRF52840 Development Kit, and am trying to control an IKEA Trådfri bulb. I'm following the commands from the SDK documentation , but it feels like they're...
So I'm trying to write a value to a characteristic I have set up as in the code below (figure 1), using the code further below (figure 2).
The sd_ble_gatts_hvx call is coming...
Hello
I would like a suggestion on the best architecture to collect data from multiple sensors in a room. Let me explain my need.
I have a room where we place multiples...
I'm trying to understand how RSSI measurement works.
According to datasheet if I understood correctly I have to issue a " TASKS_RSSISTART " command and wait for the corresponding...
I am using an nRF52840 Dongle to try and connect to a product over Bluetooth and communicate with it. I have been able to open this dongle using nRF Connect Bluetooth Low...
This behavior only occurs when connecting to the phone using the native connection procedure, it does not disconnect when using the nRF Connect app on the phone (Android Pixel...
I am trying to flash a secure DFU bootloader (compiled using my own key), a soft device, and my application using nrfjprog with the intention being to have the application...
I have implemented a bootloader without BLE that simply transfers softdevice/application/bootloader from external flash to the internal flash, performs usual validation and...
Hi,
I want to encrypt the BLE data.
If I understand it right the cryptocell can't encrypt the data sent over BLE automatically, instead the application has to encrypt...
Hi, I am working on sample projects on the subject "proprietary_rf" which includes the nRF5_SDK_15.2.0_9412b96 sdk. I updated the codes according to my own project. Finally...
I TRY TO PROCESS OTA FROM SDK11 TO SDK13, BUT ITS NOT WORK.
WHEN I SEND THE ZIP FILES, IT WILL CLOSE OUT FROM BOOTLOADER.
SO HOW DO I PACKAGE THE ZIP FILES?
