I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I am developing a device with nrf52840 soc, I need to know that there is any unique and unforgettable id in this chip that with that I could differentiate between...
Hi, Just wanted to pass this along... with the latest Raspbian (09/26/19) the thingy52 will consistently disconnect after about 90 seconds (+/- a few seconds). You can easily...
Hello,
I have two boards of nRF52840, one being central and the other is peripheral. On the central I've put the code from ble_app_multilink_central and on the peripheral...
Hello,
I see this type of query or GATT error has been asking continuously. I have gone through all the same Q&A but not able to solve my query. I have tried all the possible...
Hello Nordic support,
I was referring to the RTC example in nrf52 SDK where an interrupt is triggered on Compare Counter event. In the example, the interrupt is triggered...
I am trying to make custom BLE service to send the data from one nRF52832 to another nRF52832 but we followed the below tutorial "Bluetooth low energy Advertising, a beginner...
Hello,
We are developing a device that needs to get local binding info on init to see if it needs to send data or not to an on/off server in a remote device.
Is there...
Hi,
I'm using nRF52832 board and I'm integrating the Bluetooth beacon sending in the Bluetooth Mesh example. I've edited the Mesh Beacon example in Mesh SDK v4.0.0 with...
I am working with ble_app_uart example. I have added a new folder by name custom_folder in $(SDK_root)/, the same places where folders like library, softdevice, ble, boards...
Hello, currently im using feather nrf52840 board in arduino environment. I made some tests with BLE with TX power at 8 dBm and when boards are at line of sight signal is good...
In the SDK it suggests we use those new nrfx drivers, and says the legacy will no longer supported in the future. However, in the examples of the SDK, it uses the legacy driver...
hi
i am using sdk for mesh v3.1.0 i get my data from the uart and sending it over the mesh. i have been getting an error within the function net_state_seqnum_alloc() that...
Using SDK nrf52_sdk_16.0.0 PCA10040 S132
My code can read and write Flash using the "Data Storage Flash" interface, IE calling fds_record_write(...) and waiting for events...
Hello I am quite new to the hardware encryption topic and I have the following questions.
On a device where the MCU samples a sensor data and stores it to a external IC...
Hi .. I've a Chinese watch with NRF52832 CPU DTNO.1 F18. I'd like to change it watch face as all watch with Mediatek CPU ..
Is there an application to easily do that How...
