Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi,
Is it possible to give 3.3V to the Vdd pin of my nrf52840 to change the reference voltage of saadc to 3.3V ? Do I have to change any configurations for the same?
Hello community
I want to advertise when physical pin 0.24 is high, and stop advertising when pin 0.24 is low. For this, I based my code on the Beacon Transmitter Sample...
Usually, I programmed the Thingy 91 with the nRF connect Programmer (right now version v.3.3.3). As my Thingy did not work with the asset tracker software and only with the...
Hi,
I am trying to integrate an UARTE application code with OpenThread example(thread_mqtt_sn_client_publisher_pca10056) on my nRF52840. My application code uses UARTE0...
Dear Sir/Madam,
I need help. I am using UART to send the data in the mesh topology .and I configured mesh using light_switch source code. is it enough to send data using...
I am trying to interpret the values in the INFO.VARIANT register for the nRF52840. The datasheet states "Build code (hardware version and production configuration). Encoded...
Hi,
After following the steps for building the documentation, I always get the following error:
"CMake Error at CMakeLists.txt:92 (add_subdirectory): add_subdirectory...
Dear All, I am trying to develop a simple BLE scanner that will scan for BLE beacons and print the retrieved packages. I am using nRF5 SDK v16.0.0. I have mostly succeeded...
I'm using an SES with NRF52840, w/ SDK 15.3, and SoftDevice S140. Im working on DFU and have two components:
- a main app that already takes care of moving a FW image into...
Hi
We are using %XMONITOR to get the network status and parameters, but we cannot understand some of its response:
1), sometimes, the PLMN may be "FFFFFF" and TAC may...
Hi!
I am in the process of trying to figure out how much it is actually going to cost for our devices to support LTE-M, and I have realized that I don't actually know what...
I am trying to write a simple application to publish messages over MQTT to an AWS IoT-Core broker. I started with the MQTT_Simple and AWS_FOTA examples. When trying to do...
before the question , I hope you understand my poor English.
i make a project using nrf52840 dongle
when event of an interrupt signal occur , the chip must wake up...
Hi,
I'm attempting to wake the nrf52480 from it's sleep mode using a button input and sequentially send the command normally associated with that button without requiring...
Hello Experts,
We need to get an RF certificate for our product with nRF52840 (it's actually nRF52840 USB dongle).
In our case, the BLE stack is initialized in the central...
