I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
Hello , I tried Integrating NINA-B41 ble module with STM32F412 series board , Ble module is communicated over uart through AT command , it is working fine
BUT When I send...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi, I am using an external host with NRF54l!5 dk to test the channel sounding feature.
Can you tell me how the NRF controller supports this Cs procedure and whether the...
Dear Sirs
I try to read SoftDevice version using
ble_version_t version; sd_ble_version_get(&version);
As I understand I get version of SoftDevice in field subversion_number...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
I am trying to use the AWS FOTA library. It correctly downloads the image at 100% but always ends with a MPU Fault on the downloader thread.
I set the stack size at the...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
I followed the DevAcademy lesson on WiFi FOTA with AWS IoT, with some modifications to work with my board.
The device correctly connects to the AWS mqtt server and published...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
