Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Why is it that when NRFFW[0] = 0xFFFFFFFF SVC calls are passed on to the softdevice but when NRFFW[0] = 0x19000 they are passed on to the SVC handler of the application...
Do you have template for nRF52832/PCA10040 with s113 ?
If no, what have to change in my template for nRF52832 that works with s112:
c_preprocessor_definitions
S112...
My problem is a little bit weird: I don't get a HardFault, although I'd want so.
SDK-12.3.0 (d7731ad), FreeRTOS (from the SDK) and SoftDevice S130 (2.0.1) also from the...
Hello,
for the project I'm currently involved I'm developing additional components and changing/fixing parts/issues in the nrf5x SDK.
My client allows me to opensource...
Hi,
The examples in the SDK 16.0 for the nRF52811 all use the s112 and I woul dlike to have a NUS board (peripheral) with coded phy to talk to a nRF52840.
What are the...
Dear All,
I have a simple push-button.
Vcc-100k resistor ->> Push button --> Ground.
When I measure the current consumption when the button is pressed i get around 230...
Error while probing devices: Error occured when get serial numbers. Errorcode: CouldNotCallFunction (0x9) Lowlevel error: INVALID_OPERATION (fffffffe)
Hi all , I am encountering...
Hi,
I am using
PCA10040
SDK 15.3.0
Keil IDE
The soft device is S112
JLinkRTTViewer for debug
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10040e...
hi,
I use nrf5_SDK_for_Mesh_v4.0.0_src and pca10040 borad.
examples/dfu is successful.
But there was an error after the merge.
C:\Python27\Scripts>nrfutil dfu serial...
I setup my adc in continuous mode with sampling rate set to 200ksps, when I trigger NRF_SAADC_TASK_START, I am not getting data; unless I trigger NRF_SAADC_TASK_SAMPLE and...
I am using DSK 15.3, SES 4.30 with SD 132. The base example I am using is the ble_app_uart_c and I am adding the PWM function to drive a simple piezo buzzer.
The pwm_library...
I am looking for a way to interface with the onboard Bluetooth on the Thingy 91 as well. None of the examples (Peripheral NUS, Central NUS) etc currently work with Nrf52840_pca20035...
We have a need to verify an secp128r1 ECDSA signature. I see that this is not one of the curves supported by the CC310, but I'm looking into creating the CRYS_ECPKI_Domain_t...
The documentation says "This module is ONLY for debugging purposes and must never be used in final product". I know in an ideal world all possible errors are handled and device...
