Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am using
PCA10040
SDK 15.3.0
Keil IDE
The soft device is S112
JLinkRTTViewer for debug
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10040e...
hi,
I use nrf5_SDK_for_Mesh_v4.0.0_src and pca10040 borad.
examples/dfu is successful.
But there was an error after the merge.
C:\Python27\Scripts>nrfutil dfu serial...
I setup my adc in continuous mode with sampling rate set to 200ksps, when I trigger NRF_SAADC_TASK_START, I am not getting data; unless I trigger NRF_SAADC_TASK_SAMPLE and...
I am using DSK 15.3, SES 4.30 with SD 132. The base example I am using is the ble_app_uart_c and I am adding the PWM function to drive a simple piezo buzzer.
The pwm_library...
I am looking for a way to interface with the onboard Bluetooth on the Thingy 91 as well. None of the examples (Peripheral NUS, Central NUS) etc currently work with Nrf52840_pca20035...
We have a need to verify an secp128r1 ECDSA signature. I see that this is not one of the curves supported by the CC310, but I'm looking into creating the CRYS_ECPKI_Domain_t...
The documentation says "This module is ONLY for debugging purposes and must never be used in final product". I know in an ideal world all possible errors are handled and device...
Hello, we are developing a system that will include an nRF52832 in peripheral mode, that will be connected to from a maintenance App (or something) on a mobile phone,and will...
Hi support team,
I'm using sdk 15.0 and softdevice s140_nrf52_6.1.0 and nrf52840.
My application has strict requirements on power consumption, so I have to set advertising...
It seems like this should be a simple thing, but I can't find an example of it, and nothing I've read here seems to help.
I want my app to come up in general advertising...
I'm working with Fantel's adaptation of the nrf52840 (EV-BT840F). I have gotten the GFX example working with Adafruit's ILI9341 in SPI mode, however I am having a problem...
Hi,
How do we detect network detach in nRF9160 in a general way?
We use lte_lc to connect which blocks until we have connect/attached to the network. But how does lte_lc...
Hi,
I have a little program that is built on top of the USB CDC ACM example. This little program waits for an SPI event, when the event arrives, it reads the SPI peripheral...
Hi,
For my project I use a ble central and a ble peripheral.
I have to send data from the peripheral to the central and i use hvx indication to do that.
I have two charactics...
