I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm using an SES with NRF52840, w/ SDK 15.3, and SoftDevice S140. Im working on DFU and have two components:
- a main app that already takes care of moving a FW image into...
Hi
We are using %XMONITOR to get the network status and parameters, but we cannot understand some of its response:
1), sometimes, the PLMN may be "FFFFFF" and TAC may...
Hi!
I am in the process of trying to figure out how much it is actually going to cost for our devices to support LTE-M, and I have realized that I don't actually know what...
I am trying to write a simple application to publish messages over MQTT to an AWS IoT-Core broker. I started with the MQTT_Simple and AWS_FOTA examples. When trying to do...
before the question , I hope you understand my poor English.
i make a project using nrf52840 dongle
when event of an interrupt signal occur , the chip must wake up...
Hi,
I'm attempting to wake the nrf52480 from it's sleep mode using a button input and sequentially send the command normally associated with that button without requiring...
Hello Experts,
We need to get an RF certificate for our product with nRF52840 (it's actually nRF52840 USB dongle).
In our case, the BLE stack is initialized in the central...
The instructions are wrong -- I have verified with 3 different boards that Step 3 does not work.
Step 3 states: Click the large “+” sign on the top left to add your new...
I have written a UARTE driver, to conform to the kind of API we need, for NRF52840. It is very nearly working except that it drops single received characters and I'm trying...
Hi there, I'm trying to guesstimate the best that I can, the amount of power it would take to transmit roughly 10 kbit/s of data through LTE-M on the nRF9160. I'm just looking...
Attached is a nRF52840-DK project and an Xcode project with iOS and macOS targets. When I run on macOS the L2CAP channel is opened. When I run on iOS the L2CAP is not opened...
Hello
I would like to use the bootloader on the pca10056 in order to use the DFU with the UART.
For my tests, I programmed the pca10056 with the bootloader coming from...
While trying to read the 41 (or more) bytes length character string attribute from the device based on nRF Thread and Zigbee SDK v3.1.0 by the read attribute Zigbee command...
Hello,
i am facing issue in uart data capturing in nrf52832..
i am capturing the received uart data as shown below , but not possible to capture more uart data as if(FIFP_LENGTH...
