why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi guys,
I would like to know which pins of my MAX30102 Heart rate module connect to my nrf52832 SoC and where do they connect to on the chip?
Do the SCL and SDA pins...
Hi i am trying to reduce the adc read times to a minimum we currently have it setup for 3us acq and 32 samples so expecting something close to 160us Its getting around 250us...
Hi,
I'm trying to implement nrfutil serial DFU master in C code. I have few doubts on it.
1. Can we avoid ping packet at the start?
2. What is PNR and how we can...
Hi i'm trying to execute a code, but during the compilation it gives me a bug. The bug happens when I pressed a Button that has been programmed to restart the Ublox module...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to recover after fatal error...
To the kind attention of Nordic support team,
reading this https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059 thread,
I...
Hi, I'm using the Cyclone FX programmer to program our custom boards with the NRF52840 chip, but after programming all the hex files, the application starts straightaway bypassing...
I want to use a timer to generate a Manchester data. The fastest data rate is 3.906 K-bit. So I want to generate a timer interrupt once 128 uS. Can anyone guide me how to...
Hi,
I am using Laird's BL654 USB dongle based on the nrf52840 and would like to convert the peripheral USBD BLE UART example ( https://infocenter.nordicsemi.com/index.jsp...
Good day!
52840 datasheet states " If the power failure warning is enabled and the supply voltage is below the threshold, the power-fail comparator will prevent the NVMC...
After the MTU size exchange of 247 bytes with Android LL_LENGTH_REQ/LL_LENGTH_RSP are exchanged with 123 byte octets for TX and RX. Data flows properly after that.
But with...
Hello,
I'm working on NRF52840 drivers for custom hardware using Nordic's FatFS / SDIO drivers and a tickless FreeRTOS configuration. When I load the demo code (fatfs demo...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving "LTE link could not be established." and then rebooting.
Things I have tried...
