Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
My Win 10 is up to date. Seger' J-Link driver is OK. Here's message from log screen: Please help to find what I missed. Thanks.
08:03:35.048
Using nrfjprog library 10...
Hello,
I am currently trying to use the MQTT publisher example to send a message to a locally hosted MQTT broker (I assume I can use a local IPv6 address?). The MQTT broker...
Hey Nordic Team,
I'm in the midst of integration the nRF91. As with the nRF52 designs, less work was taken out of the RF design aspect because it has a built in balun. As...
Hi Nordic：
I burned the AP & Modem firmware in the picture below, and found that the current consumption when entering PSM is 500μA. Please help to analyze. What caused...
Hello ,
I am using freertos with nrf uart service, i could able to get these timings that seem little bit weird.
one of the pin toggled for each successful ble_nus_data_send...
Hi Nordic ,
I have a nRF52840 project development based on SDK 15.3 . Now ,I need to add DFU feature there. we suppose to use background DFU here. we will use long range...
We have been using RSSI as a signal for doing location services, however we are find that a bit challenging. From reading the literature in the field, several researchers...
Dear community,
for my upcomming project I would like to use the nRF52832. Since there also exists a development kit I started to make myself familiar with Embedded Studio...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
Hi,
I'm trying to prepare the firmware for a nRF24LU1+ in order to allow automatic driver installation on Windows.
Based on Microsoft documentation during device enumeration...
I like to provision a node in mesh with the help of computer. Shall i use serial example? Is it possible to use without interactive_pyaci to provision a node with computer...
Hi,
My questions is related to this one: https://devzone.nordicsemi.com/f/nordic-q-a/58250/short-range .
We are also developing board and range is shorter than in smartphones...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I encountered an issue, please kindly refer to the attachment for the detail.
"'' The problem is: a> Run demo on PCA10056 (BLE adv & ANT continuous scan). b> ANT Dongle...
