I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Hi, I'm trying to implement a watchdog on the nRF54L15. I configured the watchdog with a maximum window of 1000 ms, and I'm feeding it from a low-priority thread every 500...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I'm trying to connect to the EMQX(what I made on GCP) using mqtt protocal. I'm using the sample code that nordic provides in lesson. Based on the Exercise4 code which...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
Hi,
I came across this interesting game Nordic Engineers have developed and played. My company makes these displays and I would totally love to build something like this...
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
