I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
Hi
I cannot find the pin-configuration for the nRF9251 using the nRF91x1 SiP LTE firmware. I can see that the Thingy91X and the nRF9151-DK board are using different UART...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hello, guys, I am working on distance measurement project using two nRF5340DK (nrf_dm sample application). I found duration for which the distance measurement between two...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
I'm develping my application with nrf52832 and nrf SDK v17.
I'm testing SPI interface so that I can use the external flash.
When I using SPI without BLE stack,the waveform...
Hi,
Our products have been mass-produced and now need BQB certification, but the certification fails.
IC：nRF54L15 ncs2.9.1
base project: ncs_v2.9.1\v2.9.1\nrf\samples...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
Dear Experts,
I would like to better understand what exactly is accomplished by the mode-0 synchronization in Channel Sounding. My current understanding is that it seems...
