I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
Hi
nrf52833 SDK16
The following code works fine on UART 0 but not on UART 1
The problem seems to come from nrfx_uart.c
There is no support for a UART1, so...
Hi,
I've built a project out of the USBD_ACM_CDC example in which I have added a SPI master driver. This project has a timer interrupt that will shoot off every ~500us and...
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
Hi every one,
I'm a development product with chipset NRF52811, using soft device S112 and SDK 15.3.0.
My device will wake up and send data whenever I press the button...
Hello Nordic Team, I'm starting a project which consist in measure pressure in multiple points and send this data to central unit. At this point, using strain gauges with...
Hi,
I am using the Thingy 91 and I have a program, where I first read GPS, then switch to NBIoT Mode and then send the data to a server.
However if I switch the Antenna...
Hi, Nrf Connect was used as a central.When I send a data (Uart Service) from the app to the characteristic value of a Service (UUID:0x0002), the callback function of another...
Devices: nRF52840
Example: Light switch provisioner/client in one device
I have been looking into provisioner flash storage and am trying to understand at a fundamental...
Hi,
I flashed my 2 PCA10056 boards with light switch server and client respectively. As a provisioner, I am using my IPhone 6 wirh nRF`Mesh app.
After the provisioning...
Hi,
I am wondering how I would describe the capabilities of a device. Say, I were to develop a device that contains a light bulb and a fan. I could now use two elements...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832 and esp module
I want to implement Dfu process for my devices preset in mesh network and...
