Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi Team,
Please let me know can we register Multiple e-sim in Thingy:91 and nRF9160/DK? What is the procedure for e-sim registration in Thingy:91?
Regards,
Ashiq Mo...
Hi
I am testing the example ¨¨ ble_app_att_mtu_throughput ¨¨ on nRF52840 by changing different paremeters incuding data length, MTU, transmitting power and PHY.
when I...
Uisng pca10040 and SDk16.0.0 + Segger
I built and ran the GPIOTE example so I could experiment.
I want to toggle a gpio once only and then stop and I need to know when...
Hi,
Iam looking for very simple low cost wireless module which supports at least 500meters range ,please suggest a module.
I dont need lora module apart from this please...
I have latest SDK, which is nRF SDK 16.00. I have noticed that not all the examples are available for PCA 10100.
So my question is what is the difference between the PCA...
Hi,
I have compilation error to use SPI.
Checking project status Building ‘ble_app_beacon_pca10056_s140’ from solution ‘ble_app_beacon_pca10056_s140’ in configuration...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
hello.
I used 52840 act as center device.whose RX TX connected to my another MCU(MTK7688 UART). This is a IoT-GateWay. now I want to upgrade the 52840 application. BUT,...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
