I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to recover after fatal error...
To the kind attention of Nordic support team,
reading this https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059 thread,
I...
Hi, I'm using the Cyclone FX programmer to program our custom boards with the NRF52840 chip, but after programming all the hex files, the application starts straightaway bypassing...
I want to use a timer to generate a Manchester data. The fastest data rate is 3.906 K-bit. So I want to generate a timer interrupt once 128 uS. Can anyone guide me how to...
Hi,
I am using Laird's BL654 USB dongle based on the nrf52840 and would like to convert the peripheral USBD BLE UART example ( https://infocenter.nordicsemi.com/index.jsp...
Good day!
52840 datasheet states " If the power failure warning is enabled and the supply voltage is below the threshold, the power-fail comparator will prevent the NVMC...
After the MTU size exchange of 247 bytes with Android LL_LENGTH_REQ/LL_LENGTH_RSP are exchanged with 123 byte octets for TX and RX. Data flows properly after that.
But with...
Hello,
I'm working on NRF52840 drivers for custom hardware using Nordic's FatFS / SDIO drivers and a tickless FreeRTOS configuration. When I load the demo code (fatfs demo...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving "LTE link could not be established." and then rebooting.
Things I have tried...
Hi All,
I'm working on adding simple melodies (2-5 tones) to my app using the I2S module and i'm facing some problems:
How do i determine the tone?
Can i determine the...
The supl domain name doesn't resolve.... SPM: NS image at 0xc000
SPM: NS MSP at 0x20027508
SPM: NS reset vector at 0xe965
SPM: prepare to jump to Non-Secure...
To the kind attention of Nordic support team,
Let's please consider this scenario:
PCA10040 with ble secured bootloader already installed
PCA10056 with usb bootloader...
I'm confused by this because I believe I am writing to the correct LED Characteristic. The code looks like:
...
if characteristic. properties . contains (. write ) { ...
Hi
I would like to use an ENUM and STUCT within my application to maintain device state (IDLE, RUNNING etc). This state needs to update a BLE Characteristic. I have the...
