I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi!
I am in the process of trying to figure out how much it is actually going to cost for our devices to support LTE-M, and I have realized that I don't actually know what...
I am trying to write a simple application to publish messages over MQTT to an AWS IoT-Core broker. I started with the MQTT_Simple and AWS_FOTA examples. When trying to do...
before the question , I hope you understand my poor English.
i make a project using nrf52840 dongle
when event of an interrupt signal occur , the chip must wake up...
Hi,
I'm attempting to wake the nrf52480 from it's sleep mode using a button input and sequentially send the command normally associated with that button without requiring...
Hello Experts,
We need to get an RF certificate for our product with nRF52840 (it's actually nRF52840 USB dongle).
In our case, the BLE stack is initialized in the central...
The instructions are wrong -- I have verified with 3 different boards that Step 3 does not work.
Step 3 states: Click the large “+” sign on the top left to add your new...
I have written a UARTE driver, to conform to the kind of API we need, for NRF52840. It is very nearly working except that it drops single received characters and I'm trying...
Hi there, I'm trying to guesstimate the best that I can, the amount of power it would take to transmit roughly 10 kbit/s of data through LTE-M on the nRF9160. I'm just looking...
Attached is a nRF52840-DK project and an Xcode project with iOS and macOS targets. When I run on macOS the L2CAP channel is opened. When I run on iOS the L2CAP is not opened...
Hello
I would like to use the bootloader on the pca10056 in order to use the DFU with the UART.
For my tests, I programmed the pca10056 with the bootloader coming from...
While trying to read the 41 (or more) bytes length character string attribute from the device based on nRF Thread and Zigbee SDK v3.1.0 by the read attribute Zigbee command...
Hello,
i am facing issue in uart data capturing in nrf52832..
i am capturing the received uart data as shown below , but not possible to capture more uart data as if(FIFP_LENGTH...
To whom it may concern,
We know that nRF52833 DK - Development kit support to Bluetooth 5.1. I could not see antenna array on board. Product support NFC antenna. Is there...
hi，dear.
I designed the hardware according to the datasheet of NRF52832, version 1.4, Page 545,Figure 169: QFAA and QFAB QFN48 with internal LDO setup.
In the picture...
