Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello,
I have found a bug within the current (and earlier) release of the NRF SDK.
I have a project where I am using ESB to communicate. There is a primary transmitter...
Hi! I am trying to enable UARTE and Serial in my app, but somehow the nrf_serial code is not compiled because it fails the "#if NRF_MODULE_ENABLED(NRF_SERIAL)" test.
How...
Hi,
We have a legacy product which is in production using the nRF51422 using a legacy DFU.
We need to re-install some test equipment PCs with Master Control Panel which...
Hi,
I' m trying to create a TMIM easydma sequence to same an ADC. The sequence involves a write, and timer delay and a read.
Given what I'm trying to achieve, I think...
Hi ,
Is it possible to send low rate telemetry data ( 1Kbyte) per day
to smartphone VIA Nordic NFC solution.
So ... the smartphone read the stored memory in nordic...
Hi teams,
As the title describes, how can I find source/destination address inside mesh model callback functions?
Is there any API functions? Or should I modify callback...
During the pairing phase, LTK will be generated for the secure connect, and no LTK will be generated for the legacy pair, but LTK will be generated for the subsequent bonding...
Where can I find documentation of http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.0/nrf/samples/nrf9160/serial_lte_modem/README.html#serial-lte-modem IP UDP low power...
Hi, I am trying to create a custom_service for my application.
I am using nRF52832 SDK_16
SES
I want to create the BLE_SERVICES
which has send characteristics and...
Hi,
I converted ble_app_beacon example to Segger Embedded Studio (using version 4.30b), as per the instructions in the link https://infocenter.nordicsemi.com/index.jsp?topic...
I configured a NRF52832 with non-scannable and non-connectable as well as scannable/connectable advertising. Everything is working fine.
But I want to fully understand the...
I have an existing phone app (using the traditional GATT system), and I would like mesh-enable my products so that if the products can see each other, then the phone can connect...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
