We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I'm going to write to inquire about Bluetooth Low Energy Device Beacon which will be smallest in size and can operate with coin cell battery and also able to communicate two...
Hello,
While building a custom board, I need 52832 to communicate with a modem at regular intervals, send AT commands and read modem responses. nrf_serial library in IRQ...
In the documentation for “Bootloader and DFU …” / SDK16.0.0 is written “you can use such a bootloader, for example, to switch between several applications”, but I can’t find...
I connect one central and two peripherals
Both peripherals set the connection interval to 100
Observing PA / LNA shows that one is communicating in 100ms
But the other...
Hello.
I have question about output OOB and public key.
I create my Android app for Thingy Bluetooth mesh purposes. I would like to start output OOB process (then Thingy...
Hi,
I am using the nrf_log_backend_flash in SDK15.3 with IAR 8.32 on Window10. From what I see in the release notes, no improvements were made for 16.0.
In my application...
Hi,
Good day!
Statement of porblem: We are developing appliction using nrf52832. In our application we have Capacitive touch button and capacitive wheel sensor for user...
Hi,
I am using bootloader and application based on SDK15.3.0 and SD s140_nrf52_6.1.1_softdevice.hex.
I am also using our own BLE transport layer in application to receive...
Hello, I can see in the datasheet of the NRF52840-CKAA-R that the recommanded inductor value for DCCH is 10uH +-10% (configuration no. 4). Unfortunately, we experience some...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
