At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I was able to complie many of the nrfx/samples under SDK v2.5.0 using VS Code IDE but cannot successfully compile any under SDK v3.0.0 .
The [Building and running]: <.....
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I'm use latest ncs source code and nRF54L15DK PCA10156 to test Bluetooth Channel Sounding, but i'm find the result not very accurate, and also echo such like warnings:
...
I am currently using ncs 2.9.0 on a custom board using the internal ldo and internal clock settings. It is a simple project where I take and indicate an adc and internal temperature...
I'm trying to use parity UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_PARITY_NONE...
Hi,
I need to use the GPIOTE with interrupt function with nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board.
So I created a build...
For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Hi,
I couldn't grab BLE 2M packets using wireshark and nrf52840 dongle, so I switched to using the nRF connect for desktop. But it can not detect the dongle.
The nRF...
Hi,
We developed a custom board based on the nRF54L15 SoC. We realized many current consumption tests with regulator configured in DC/DC mode. These measurements are in...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
