Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi everybody, I am a beginner and I need your advice to start to modify the example of Radio Receiver/Transmitter. Ultimately my goal is to measure the time between the reception...
Error message from KEIL CMSIS D/L :
Update available for ARM::CMSIS (installed: 5.6.0, available: 5.7.0) Update available for ARM::CMSIS-Driver (installed: 2.5.0, available...
I have developed an bootloader operating with external flash for image storage. For the use case it is not acceptable to put the device into an inoperable (no-application...
Hello,
I've been looking at this post devzone.nordicsemi.com/.../ in regards to characteristic lengths.
I'm still not clear on the matter. Currently I have initialized...
Hi, I'm confused how to do fota of mcuboot on the nrf9160.
The source code is public on github in this branch: https://github.com/ExploratoryEngineering/nrf9160-telenor...
I just installed NRF Connect on an Archlinux via the AUR , but I cannot install any app. I even upgraded the package to 3.3.3, but I always get:
Error
Unable to...
Environment: nrf9160DK v0.8.2 nRF Connect SDK v1.2.0 Modem firmware: v1.2.0 Toolchain: gcc-arm-none-eabi-9-2019-q4-major-win32 I started with the nrf mqtt_simple sample and...
Hi,
I have bought TMP117 with NRF52832 from Nordic, a wristband becon module. I am new to this boards. I want to create my own Android app. I want to know how to do this...
Helllo,
i'm using a custom shield with the Thingy:52.
I need to control some TWI chips, but these chips (ADG728) have only one register.
I have done a specific driver...
In the nRF5 SDK v15.0.0 there is an example for beacon. (in my case ble_app_beacon_pca10040_s132)
This example works fine and acts as a non-connectable unidirected beacon...
Hi, I'm trying to add Characteristic User Description 0x2901 and CCCD 0x2902 to a characteristic. It seems 0x2902 always comes before 0x2901 in attribute table. Is there any...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
