Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am working with the S140 softdevice v6.1.0. The message sequence charts located on the Nordic infocenter are great help. Question: are they available in a printable form...
Hi,
Is there any editable software available that I can use to create a custom interface between my PC and my nrF58210 module. I have been successfully using the Nordic...
How to program flash with the output HEX file and SoftDevice file using NRF52-DK.
When programming with the output HEX file the device does not work, I need also HEX - SoftDevice...
I'm trying to set up a project with SDK 16.0.0 using FreeRTOS with the softdevice. The device will be battery powered and therefore power management capabilities are required...
Hi all,
I am trying to generally gain a better understanding of the GPIOTE module and how it can benefit myself in the project I am working on.
I am essentially attempting...
Hello
Does the nRF5280 include Schmitt-trigger inputs on the GPIO pins?
If yes, what are the voltage threasholds for the rising- / falling edges?
(Can't find anything...
Hi,
How does disconnect work in S112?
In the ble_template project, I did not find anything in DISCONNECT event.
static void ble_evt_handler(ble_evt_t const * p_ble_evt...
I have a nrf52833 pca10100 which can connect to nRF Connect Desktop to program fine. EVBW833 should have the same chip DK but it is not being recognized. Is there a way I...
Hi
On my custom board, I have an external flash connected via SPI. . The nrf runs on mfw 1.1.0.
Without activating the flash, I get an average current consumption of around...
Hello,
I am using nRF51 DK and it is programmed with s130 soft device and uart application hex file with nFGo studio.
It programmed successfully but device not showing...
Hi, guys. The codes in Nordic Github like
Android-nRF-Mesh-Library / Android-BLE-Library / etc
are written in Java.
https://medium.com/@nithinjith.p/ble-in-android-kotlin...
Hi,
I'm currently evaluating the nRF9160 chip as a potential replacement device in our internet-connected products. In most cases the zephyr documentation and examples are...
Hi,
I modified your USBD BLE UART Example by commenting out the button and LED code to run on a dongle with J-Link debugger soldered on.
I removed the bootloader and set...
Hi I am new to NRF52832. I am using SDK 16, Multlink Central (ble_app_multilink_central).
Here are my questions:
1) The software keep resetting when I flashed the code...
Setup nRF52840 DK S140 nRF52 SDK v16.0.0 nRF SDK for Mesh v4.0.0 Goal I would like to be able to disable the Mesh stack and all radio operations so that my application can...
