The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
If we want to obtain sets of five "Bluetooth stylish temperature sensors, do you have a selling point in The Netherlands? If not maybe a way to obtain this by mail or parcel...
Hi!
I am coding soft for nRF52xx. Having looked through the examples I've got one question.
In the preprocessor defined:
NRF52_PAN_24
NRF52_PAN_25
NRF52_PAN_26
NRF52_PAN_27...
We have a nrf51822 chip connected to an arduino-like device. We need to use UART for communication, but without firmware modification the master chip doesn't support USART...
Hi.
I'm using PCA10028, SDK10.0.0, S130. I'm a beginner.
If I want to download hex files(soft device and fw code) though UART port, is it possible?
If possible, could you...
Dear all,
I checked the SDK release note and found Nordic decide not to support CMSIS anymore.
As I developing with 52832, I try to use FreeRtos to control the whole system...
Hi: I want use freeRTOS on nrf51822 based on sdk10. But when I open the example project"blinky_freertos"and try to use it, The keil5 manage run-time environment tell me "install...
I am developing a BLE peripheral with SDK9 and SD110. The PPCP are 80-400ms, 5 slave latency and 5s supervision timeout.
I am currently running some blocking code in response...
I'm having trouble with my call to ble_advertising_init when using S130 soft device v2.0.0 on an 10031 device with SDK 11.0.0, I'm getting error_code 7.
When I try and...
Hello everybody,
Does the S312 v2.0.0 handle BT operations completely independent for each BT connection? Can I read/write from/to different characteristics on different...
Hi!
I am studying some program code of BLE examples.
I have a doubt about what does the evt_handler() do.
E.g.
in the example "ble_app_hrs_s130_pca10028"
static void...
