NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
I will try to use the s110 8.0.0
But I can not find the sdk installer from the website.
Three months ago, when I visited the website, there is a SDK 6.xx.xx Installer...
Hi.
I'm currently receiving advertisement packet from beacon scanner app. (nrf51822)
(ble_peripheral/experimental_ble_app_multiactivity_beacon/hrs_scanner)
I tried...
Hi, I am here in the use of Flash memory data when there is a strange question to consult.
Due to my side of the application, you need to enter each case sd_power_system_off...
Using nRF51 SDK 10.0, it seems like many debug prints are incorrect, triggering a GCC format warning resulting in a compilation error with -Wall turned on.
A workaround is...
I'm using a custom designed PCB around the NRF51822 that broadcasts accelerometer readouts on a characteristic.
The application is based on s110 uart example and has been...
i wantto compile ''ble_app_hrs_c'' from sdk
but it always show up likes
" C:\Program Files\CodeBlocks\MinGW\include\SDK 7.2\examples\ble_central\ble_app_hrs_c\main.c|19...
keil use pclint, it will give lots of info message or warning message.what 's the best configuration to filter these info message ?? just display the error or warning message...
Hi
I'm trying to test UART over BLE using A custom board with a nRF51822,S110_NRF51822_7.1.0
SDK 6_1_1, Code is Github "NordicSemiconductor/nRF51-ble-app-uart-static-passkey...
I'm a beginner, the question might be simple but its really important for me.
What would the current flowing through Empty nrf51822 when it is completely erased or empty...
In bootloader of sdk9
I find
ble_gap_addr_t addr;
err_code = sd_ble_gap_address_get(&addr);
APP_ERROR_CHECK(err_code);
// Increase the BLE address by one when advertising...
Dear sir,
We are using the NRF24LU1P-F32Q32-T chipset.We have unmounted chip that we are using for our application .We have made a pcb developement board on NRF24LU1P-F32Q32...
Hi,
In my project I am using rev3 nrf51822-QFAA chip set with s130 soft device.while I compiling getting the error "region RAM overflowed with stack". Then I followed some...
