Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
Hi, I want to get the RSSI values as much quick as possible. I have written a code which is transmitting at 10Hz for instance(that is sufficient). But The problem is that...
Dear Nordic Developers,
I'm trying to write some data to a slave and when the slave gets the write command sends back a notification. My problem is that I send the write...
I would like to use nRF51422 in commercial product and I use your SDK. There are 2 files: app_uart.h and app_uart_fifo.c that I would like to modify a bit. I would like to...
Hi,
I have PCA10028 dev board and Fujitsu MBH7BLZ02 BT module.
I have successfully modified some sample code and when I flash it to nRF module on the PCA board, the...
Hi,
I ordered a few couple NRF905 a few months ago. Now I wanted to re-order a few hundred pieces the seller told me that they have "C series".
What is NRF905 C series...
Hi,
Is there a uart example for the NRF51 Dongle(PCA10031)? If not, how would I go about implementing uart on the dongle to connect to the Android NRF Uart app?
Tha...
Hii all,
I would like to create a project that take an input from any Bluetooth device and display it on display device like EPD. Till now I just hard coded the image and...
Hi all,
I have two NRF24LE1 devices, device_A for send data and device_B for receive data, the protocol data included in a 10-bytes length arrary(buffer).
In device_B...
I'm trying to understand whether my callback assigned to the data_handler variable during initialization of the Nordic UART Service gets executed in an interrupt or somewhere...
I know there have been a ton of topics about this but I've tried pretty much every solution I can think of and I cannot seem to figure out why my sleep current is consistently...
Hi,
I'm facing a very critical issue.
I need to send a time critical data from a ble sensor device to a Camera device acting as a ble central device.
Due to lack of full...