Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I am trying to program a nrf51822 module using the nrf51-dk.I have made connections as per the nrf51-dk user guide, but sme is not working...
I am using the Vdd of the...
Hello all,
In a network of sensors with power constraints in a room which protocol is the best?
Newer devices seem to use BLE but I don't want to discard good old nrf24l01...
HI, I try to turn on the OLED.
I can not confirm that the lights turned on
I want to change background color.
What should I do?
Currently being output as shown...
I have installed Keil v5.18a
and have installed MDK for nRF51-DK.
Examining the basic LED blink examples showed that in some projects, the 'bsp.h' which would be the header...
I just setup Eclipse and trying to compile.. I was getting warnings.. I think I have installed all the relevant packages.. But still getting following warnings. Am I missing...
Hello! Developer,
Does anyone know how to transfer and store the value as big endian on memory address on nRF51 and send it over BLE to display value on MCP as big endian...
Hello!
I'm trying to get the 16 bit ADC value as 2 of 8 bit array from nRF51 development kit over bluetooth to MCP, but when it displays on the MCP the value is "swap"...
Is it a good idea to use nRF51 standalone as an Application Processor and also as BLE connectivity chip?
OR
Is it a good practice to use a separate Application Processor...
I have a question on - to me - seemingly weird behavior about copying data out of the event from the soft device.
Situation: I have a 32 bit integer characteristic which...
Hey all!
Newbie here. I developed and tested some code on an NRF51DK easily enough using mbed, and now I'm trying to put it onto a PTR5518 module from Xuntong (which I...
Could you rub my nose in Bluetooth SIG Core or just explain what does chip do when switching to very noisy channel? For example Wi-Fi working very close to our device.
Hello:
I have read the documentation but I cannot determine if INPTR and OUTPTR can be set to the same memory address? I will try it to see what happens but it would be...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Everyone,
I found out on that ble_app_power_profiling application is developed for Lower power current consumption....as It keeps system in the system_off_mode until...
